StrutTech® Specifications

1.0 Scope 1.1  This specification covers the requirements for the StrutTech non-metallic channel framing system. 2.0 System Requirements 2.1 To provide single source responsibility, the channel framing and components including purchasing options after startup, the supplied system (including pipe clamps) must be interchangeable with industry standard 1 5/8” steel and fiberglass channel framing systems. 3.0 Materials 3.1 This specification is for Polyester (standard) or Vinylester (premium Corrosion Resistant resins as required for all fiberglass materials. Polyurethane thermoplastics are required for injection molded components. 3.2 Flame spread properties shall be as follows: Vinylester Fiberglass (Series VF) Class 1 ASTM E-84 Polyester Fiberglass (Series PF) Class 1 ASTM E-84 Polyurethane V-O UL 94V PVC (Capping Strip) 5V & V-O UL 94 3.3 Fiberglass Channel physical properties shall be as follows: Izod Impact ft.lbs./in305284 Longitudinal Vinylester Transverse Vinylester Longitudinal Polyester Transverse Polyester Tensil Strength (psi) 37,500 10,000 30,000 7,000 Tensil Modulus (psi) x 10 6 3.0 1.0 2.5 0.8 Flexural Strength (psi) 37,500 14,000 30,000 10,000 Flexural Modulus (psi) x 10 6 2.0 1.0 1.6 0.8 Compressive Strength 37,500 20,000 30,000 15,000 Shear Strength (psi) 6,000 5,500 5,500 5,500

4.0 Channel Framing & System Components

4.1 Channel Framing Series 100 & 200

4.1.1  All fiberglass channels shall be manufactured using either vinylester
or polyester resin.  Resin selection must meet requirements of the StrutTech
chemical resistance chart.  Fiberglass channel sizes shall have polyester surface
veil over 100% of the surface to provide protection against degradation from
ultraviolet light.

4.1.2  All series 200 channel shall be supplied with integral notches 1” on center. Notches shall be located on the interior flange to prevent slippage of pipe clamps and fittings after installation.  In lieu of notched channel, unnotched channel maybe used if the vertical channel sections supporting the horizontal piping are provided with stop lock hardware at each pipe clamp to prevent slippage.  Stop lock hardware combines a channel nut, bolt and mounting plate attached under the pipe clamp.

4.2 Pipe Clamps

4.2.1  Adjustable Pipe Clamps shall be non-metallic and non conductive,
manufactured by the injection molded process using thermoplastic polyurethane. Maximum pipe diameter supported by adjustable clamps shall be 3 inches.

4.2.2  Glass Filled Fixed Pipe Clamps for pipe and conduit under 8 inches shall be non-metallic and non-conductive; manufactured by the injection molded process
using thermoplastic polyurethane or polyester.  Resin selection must meet requirements of the StrutTech chemical resistance chart.  Fixed pipe clamps for pipe and conduit over 8 inches shall be thermoset vinylester fiberglass, and shal be manufactured by either hand laminations or resin transfer molded.  Injection molded parts for pipe and conduit sizes over 8 inches are not acceptable.

4.3 Channel Fittings & Post Bases

4.3.1 All channel fittings and post bases shall be made from glass filled polyurethane or polyester. Resin selection must meet requirements of the StrutTech chemical resistance chart.

4.4 Fasteners

4.4.1 All fasteners shall be made from one of the following materials: Glass filled polyurethane, vinylester fiberglass, stainless steel. Resin selection must meet requirements of the StrutTech chemical resistance chart.

5.0 Acceptable Manufacturer

5.1 StrutTech Redmond, WA 425-885-2805